Pow-R-Quik Hydraulic Starting Systems
Pow-R-Quik Hydraulic Starting Systems
POW-R-QUIK SMART-R-VALVE
Pow-R-Quik Smart-R-Valve; both HS-22 and HS-36 series are offered with this amazing product. Prevent down time with this easy to install ready to go right out of the box starter. There is nothing to adjust and nothing to worry about. Get the Pow-R-Quik Smart-R-Valve. The Soft Engagement Valve. Pow-R-Quik Smart-R-Valve Say Goodbye to Pressure Spikes That Hammer Your Pow-R-Quik Hydraulic Starting Systems.
The Pow-R-Quik Smart-R-Valve™ Advantage: Ed Z., a Test Engineer and Pow-R-Quik customer says: “We set up our test rig so we could break the starter drive and the nose cone of our test starter with just one cycle. With the addition of the Pow-R-Quik Smart-R-Valve™ to the Pow-R-Quik Hydraulic Starting Systems with the same pressures and flow we have gone thousands of cycles and the pinion and the drive looks like new.”
 |
HS-223 Series Starters P/N 6-10-601
- Flow rating: 40 GPM
- Fluids: Mineral Based or Synthetics
- Viscosity: 7.4 to 420 cSt (50 to 2000 SUS)
- Consult factory for extreme ambient temperature applications
- Max Operating Pressure: 3300 PSI (227 Bar)
- Temperature Range:-40° to 180° F
- Seal material
- Viscosity: 7.4 to 420 cSt (50 to 2000 SUS)
|
HS-360 Series Starters P/N 6-10-603
- Flow rating: 40 GPM
- Fluids: Mineral Based or Synthetics
- Viscosity: 7.4 to 420 cSt (50 to 2000 SUS)
- Consult factory for extreme ambient temperature applications
- P/N 6-10-603
- Flow rating: 40 GPM
- Fluids: Mineral based or Synthetics
- Viscosity: 7.4 to 420 cSt (50 to 2000 SUS)
|
 |
Pow-R-Quik Hydraulic Starting Systems Components
 |
Hydraulic Starting System Hand Pump
Hand Pump Specifications:
-
The Pow-R-Quik hand pump recharges the hydraulic starting system
-
Double acting pump style, 20 cc per cycle displacement
-
3000 psi maximum, Buna seals
-
Included but not shown is a 36” operating handle with grip
-
All steel construction except for piston bushing which is brass
-
Heated treated steel pins and linkage
-
Low friction O-ring piston shaft seal
-
Hard chrome plated piston O-ring surface
|
 |
Hydraulic Starting Systems Reservoirs
Reservoirs Specifications:
-
10 L (2.64 gal)
-
20 L (5.28 gal)
-
30 L (7.93 gal)
-
Removable top
-
Sump Strainer
-
Vented Cap
-
Mounding Tex
|
 |
Hydraulic Starting System Piston Accumulators
Piston Accumulator Specifications:
-
Construction: Certified seamless tube
-
Max. working pressure: 21 Mpa (3000 psi)
-
Test pressure: 35 Mpa (5000 psi)
-
Safety factor: In excess of 4:1
-
Seals: Nitrile (standard)
-
Nominal volumes in liters: 5.5, 12.0
-
Contains relief valve- unloading valve check valve
-
Needle valve for unloading starting system to reservoir
|
 |
Hydraulic Starting System Foot Valve
Foot Valve Specifications:
-
These valves provide a reliable means to control a hydraulic starting system
-
Foot Valve Specifications:
-
Max. working pressure: 21 Mpa (3000 psi)
-
Flow rate: 3/8” NPT ports, 75 L/ pm (20 gpm)
-
Hydraulic Starting System Hand Pump
-
These valves provide a reliable means to control a hydraulic starting system
|
 |
Hydraulic Starting System Hand Valve
Hand Valve Specifications:
|
|
Hydraulic Starting System Manifold Valve Block
Manifold Valve Block Specifications:
- Accumulator, reservoir, pump, and gauge connections
- Contains relief valve- unloading valve check valve
- Needle valve for unloading system to reservoir
- Relief valve: 3000 psi
- Unloading valve: 3000 psi
|
http://hydraulicstarters.ca A Division Of Strumco Air Starter
