• 780-468-0050
  • sales@strumco.com
Strumco

PRQ 224 Series Hydraulic Starters

Diesel Fuel Engines 10-49 Litre Liter, Gaseous Fuel Engines 20+ Liter

 

For a comprehensive list of model and replacement part #’s click HERE.

Features Of The 224 Series Include

  • Industry exclusive 18 month warranty.
  • New common model # 6-HSV-224 RH1 PQS79.
  • 113 ft-lbs of torque over the entire RPM range — suitable for diesel engines 10-49 litres in displacement and gaseous fuel engines over 20+ litres.
  • New HSV starter with integrated “Soft Start” eliminates mounting an external soft start block.
  • HSV model with integrated “Soft Start” allows complete protection of the engine ring gear and starter pinion by “pre-engaging” the pinion, eliminating the shock load of a typical hydraulic starter. Because of the friction clutch drive and soft start it offers high level of protection against operator error (ie; engaging into a running engine).
  • New common model # allows the same starter to be installed on many of the common engines used on well servicing equipment (CAT3400 Series and 3508, Cummins QSK30, QSK38, QSK45, MTU Engines) without any modifications (same part number works with other engines)
  • New common model # allows the same starter to be installed on many of the common engines used for gas compression (CAT3400 Series and 3508, Waukesha VGF H24, L36 and P48) without any modifications (same part number works with other engines)
  • Pinion housing rotates in 30° increments allowing for installation flexibility.
  • Severe duty gear type hydraulic motors which resist damage to contamination and have an extremely long service life. Maintenance, if required, is simple and cost effective.
  • Simple, cost effective maintenance of the starter end with no need for special or proprietary tools.
  • More than adequate torque to start any engine even in -40 degree weather.
  • Standard rear hydraulic ports for straight forward installation.
  • Standard case drain for motor protection
  • Standard weep holes indicate internal seal failure
  • Available with a 12v or 24v ON/OFF valve, with included built-in hydraulic system protection and manual override.
  • Available engineering support from the factory on special projects and hydraulic system mapping.
 

Tech Specs

  • Recommended Engine Size — Diesel 10-49 Litre, Gaseous 20+ Litre
  • Hydraulic Supply Pressure — 1500 – 3000 PSI (3000 PSI Recommended)
  • Hydraulic Flow Required — 25 – 42 GPM
  • Torque @3000 PSI — 113 ft-lbs
  • Operating Temperature Range — -40°C – 82°C
  • Standard Mounting Flange — SAE #3
  • Standard Pinion Characteristics — 11T 6/8DP
  • Rated Pinion Speed — 3000 RPM
  • Weight — 63Lbs
    •  

    Complete List Of Model #’s

    HSV Starters Have The Soft Start Integrated From Factory, HS Starters Utilize Either An External Or No Soft Start.

  • 6-HS-224 RH1
  • 6-HS-224 RH1 RD
  • 6-HS-224 RH1 PQS79
  • 6-HS-224 RH1 RD PQS79
  • 6-HS-224 RH1 L/M
  • 6-HS-224 RH1 RD L/M
  • 6-HS-224 RH1 PQS79 L/M
  • 6-HS-224 RH1 RD PQS79 L/M
  • 6-HSV-224 RH1
  • 6-HSV-224 RH1 RD
  • 6-HSV-224 RH1 PQS79
  • 6-HSV-224 RH1 RD PQS79
  • 6-HSV-224 RH1 L/M
  • 6-HSV-224 RH1 RD L/M
  • 6-HSV-224 RH1 PQS79 L/M
  • 6-HSV-224 RH1 RD PQS79 L/M

    • Available Service Kits

    Service kits contain the most common replacement parts when doing a repair. Most other parts are available and in stock.

  • 6-3-184 — Standard RH1 Starter Service Kit
  • 6-3-188 — PQS79 Starter Service Kit
  • 9Y6089 — SAE #3 Mounting Flange Gasket

    • The above starters are fully supported by Strumco and the factory. Service kits, parts, and common starters are available and typically in stock. Please contact Strumco for more information.